Tools

HOW TO PRESERVATION ELECTRIC WEED WACKER ?

best electric weed wacker
Electric weed wacker to do the job instead of human hands. In general, there are some basic types of the weed wacker as:

– Self-propelled weed wacker: self-propelled weed whacker powered type of engine thrust. When the engine operation, the engine will be born with some of the machines rotates. This torque is transmitted to the actuator of the machine and finally, to the wheels of the machine makes the machine move.
– Mowers driver: this is the format used a weed wacker to cut the grass area of the flat terrain. Finished cutting the grass is collected in barrels collected by the vacuum of the machine.
– Mowers pushing hands: do not use the engine type, this means moving series is due to human propulsion.
When the wheel is turning at the funeral was also recently wrapped filming grass weed wrap and put into the gap between evidence and blade of grass and the grass is cut then.
This machine is very suitable for small gardens and very good for middle-aged and elderly.
Lawn just moderate exercise can improve the human condition, improve the elderly’s health.
– Mowers bring shoulders: this is the weed wacker is used most commonly.

In addition to cutting grass, they are used to cut rice, cut small trees as forest clearance
The newest type of weed wacker use electricity to run, so how to use the best electric weed wacker. Take a look at our guide

Electric weed wacker
Electric lawn mowers are broken down into the model and wireless phones.Both are relatively quiet, often produced less than 75 decibels, while a petrol weed wacker as 95 decibels can grow older.

Electrical wire cutters (corded electric weed wacker) is limited to the extent of their power cord tails, which can restrict the use of the lawns extending to the outside than 30-45m from the nearest power outlet is available.
There is an additional danger to the machine accidentally cut through cables, which stops the mower and could put users at risk of receiving an electric shock hazard.
Install a residual current device (GFCI) into the socket can reduce the risk of shock.
Electric mowers Wireless (Cordless electric weed wacker) is supported by a number of rechargeable battery (typically 1-4) 12-volt / battery charger.
Typically, larger battery means more running time.
The battery can be placed in the interior of the weed wacker or outside.
If outdoors, depleted batteries can be quickly exchanged with rechargeable batteries.Cordless mowers maneuverability of a gasoline-powered mower and environmental friendliness of a wire cutter, but more expensive and less available in models (especially self-propelled) than both.

Using electric weed wacker effective:
– Wear protective gear when operating the machine.
– Do not let the blade crash into hard objects during cutting.
– The region must operate the distant people and things in a radius of 15m.
– Do not touch the blade when the machine has not stopped spinning.
– Do not start the machine when it detects damage or loose screws.

Check the weed wacker before operation
– Check the blade
– Check the tightening of bolts and screws of the blade.
– Check the warping of the blade.
Launch electric weed wacker
– Turn the switch “OFF” position to the “ON” to close
– Pull the hand pulling the strings until both hands are hard quickly and decisively pull the remaining piece of wire to the engine.
Stand machine
– Brushing smallest throttle position
– India closed position switch in “OFF”
– The air filter
– Remove the air filter out.
– Wash the air filter with kerosene.
– Installation of the wind filter and hood on the machine after cleaning.
Maintenance spark plug
– Remove the spark plug 3.1 out spark plug cap. Remove the spark plug out.
– Hygiene in extreme grime cling spark
– Check the spark plug gap poles, appropriate openings of 0.6 – 0.7 mm.
Curing weed wacker
– Check the air filter when operating the machine.
– Check blade of grass, throttle cable openings, safety status bolts, nuts when operating the machine.
– Clean the air filter after 50 hours of work
– Trigger gap adjustment after every 100 hours of operation
– Check the machine and parts, if not boot
– Remove the parts and dust filter bags if there are not rules
If the machine does not boot please bring dealers to repair.

Leave a Comment

Your email address will not be published. Required fields are marked *